Blue iris activex download3/16/2024 So now you have two distinct networks that can't talk to each other. So now my guess is he plug the NVR into his router. One obvious clue is that the NVR is running DHCP and assigning address to cameras. I think the problem stems back to what I've said all along, the PoE version of the Dahua/Q-see NVR is acting a router. Other people here posted that they were able to add additional Dahua branded cameras to their Q-See NVR from Costco so that's not the problem, the problem is likely his network topography. He has additional cameras, I'm assuming under the 4 camera limitation of the NVR that are connected to another switch. The NVR has DHCP running and assigns an IP to the two included cameras. He bought a 4 channel NVR with PoE built in. If it is possible to FW upgrade it, I'd like to do it. I guess I wouldn't be as insistent about this if when I bought the device they said the 804 could support more cameras than 4 by adding a switch. They are forwarding my ticket to the firmware peeps to see if anything will be possible. I have the HDMI from the NVR split out to displays around the house and would like it to handle more than 4 cameras in the live feed and recording. They want me to use PSS to access the other cameras, but I explained that isn't my goal. Just got off the phone with q-see support. I have watched q-see's site for a firmware update and seen none, do they not post new versions unless people contact them for the latest? I have 2.610.qs00.0.buildĪnd do you happen to know if I can flash my unit to act like a 8016? " title="Applause" /> Unfortunate that I am still stuck with 4 cameras. And since I don't have to contend with it trying to hand out DHCP addresses on my network there are no conflicts. My NVR's LAN was running different (in the 10.x.x.x world) so that isn't a problem. I had done a search previously while the cameras were on my main LAN, but perhaps I had something wrong at the time. I think the piece I was missing was that it could find cameras over the WAN port. I poured over the documentation and searched online, as well as tried a bunch of configurations but I just couldn't get it to connect. I'm actually starting to learn towards giving the AvertX system a try. I wonder if the QC804 thru QC8016 are the same hardware and I could firmware update my 804 to support more cameras. I'm most likely moving away from Q-See since their techs repeatedly told me I could just add more cameras to my QC804 and it would adopt them, but so far I haven't been able to get this to work at all. Theoretically it is all software solvable. This is something I hope Q-See (Dahua) and other manufacturers think of in the future. I can assume there may be a limitation where the cameras only want to be accessed by one device at a time, but that wouldn't be a problem if you were using the NVR as your main access to all your cameras.Īnyway, I know I laid out the obvious there - but I didn't want any confusion. So now picture going into the NVR setup, telling it to also search for cameras on the LAN/WAN side and adopt them. They will get a DHCP address from my router like everything else on my network, just like the 804 does. My home network switch is a 16 port PoE switch, and is connected to an ASUS RT-AC66U router (HECK of a router by the way if you can afford it) - I want to plug the extra cameras into my main home network. In other words - Say I buy a bunch of extra PoE Q-See cameras along with my QC804. What would truly impress me is if the Q-See NVR's were designed smart enough that you could access cameras both on it's internal PoE switch, as well as as the network LAN (or WAN if you set it up that way, but it's LAN port) anyways the cameras that i am trying to use are not built in DHCP, but i can change manually the gateway and subnet and IP addres, so I did and it didnt work The Q-see tech support were very nice but didnt answer my question, the POE switch built in the NVR has 4 port and automatically assigned IP to the cameras connected to using the 10.1.1.1 as gateway. My ovnif camera work fine in some software like milestone, alnet, blue iris and NUUO and this is the url that i enter The defaul port for my ovnif camera is http: 80 and rtsp: 554, password : admin and user id admin. where can i enter the rtsp url for make the connection? DVR has the option for OVNIF cameras where you specify the IP addres, rtsp and HTTP port, user and password and it didnt work! using the rtsp for my camera ovnif can i connect to the NVR? I just bought the NVR QC804 with 2 720P cameras, i have another camera and it is ovnif, works perfect with several manufacture software, my question is:
0 Comments
Leave a Reply.AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |